WEC - When Excellence Counts

WEC, since 1987, is your One-Stop quality manufacturer and distributor of metal lockers for all types of applications.

Your One-Stop Source for All Things Storage, Convenience, Selection and Savings. Biggest Selection, Best Prices, Nicest People

Angle Iron lockers are built within a 1”x 1” x 1/8” angle iron frame. The 1/8” thick angel iron exoskeleton creates extra strong locker edges and provides a solid framework. Equipped with diamond perforated doors and sides, this locker offers a high degree of air flow.

All Angle Iron lockers are built with the top (16 Gauge), bottom (16 Gauge) and back (18 Gauge) panels spanning multiple lockers, reducing seams and adds rigidity and strength.

These lockers are available in 1, 2 & 6 tier. Locker Groupings: The unit growth factor of the Angle Iron locker is not the same as the All Welded Plus locker due to its one of a kind construction.

The intermediate vertical door frame channels are all common between openings in the Angle Iron locker.. The hinge of one door is welded to the left side channel and the latch of the right door is welded to the other side.

Groupings
Nominal Frame Widths.	Frames in Groups	Width of Group	Nominal Frame Widths	Frames in Groups	Width of Group	Nominal Frame Widths	Frames in Groups	Width of Group
12”	5	60”	15”	4	60”	18”	3	54”
12”	4	48.20”	15”	3	45.25”	18”	2	36.33”
12”	3	36.40”	15”	2	30.50”	18”	1	18.67”
12”	2	24.60”	15”	1	15.75”	24”	2	48”
12”	1	12.80”				24”	1	24.50”

1.	ADA Compliance: Lockers are to meet the Americans with Disabilities Act, accessibility guidelines. They shall have recessed handles and shall be single tier or lower opening of a double tier locker. Locker bottom shall be a minimum of 9” off the floor, or an extra shelf placed 9” off the floor. Single tier lockers shall have a shelf 48” off the floor. Doors assigned for handicapped use shall have an appropriate symbol sign.
1.1	Submittals: Submit under provisions of Section 01 33 00. Shop Drawings shall show dimensioned plans, elevations, and sections.
1.2	Delivery, Storage and Handling: Store product in manufacturers unopened packaging until ready for installation to protect the locker finish and adjacent surfaces from damage.

2.	Acceptable Manufacturer: WEC, which is located at: 5355 Distriplex Farms Drive; Memphis, TN 38141; Phone: 901‐366‐ 5767; Fax: 901‐366‐0093; Email: sales@itswec.com; Web: www.itswec.com
2.1	Material: Steel parts shall be mild cold‐rolled commercial quality steel, capable of taking a high grade enamel finish.
2.2	Door Frames: Shall be continuous 1”x1”x1/8” pretreated angle iron steel.
2.3	Doors: 14 gauge steel with double bends on vertical sides and a single bend on horizontal sides.
2.4	Handle & Latching: Single Point Latching with Recessed Handle with integral pocket and pull 20 gauge brushed stainless steel securely fastened to door with two lugs and a positive tamper resistant decorative fastener. Pocket Depth shall be sufficient to prevent a combination padlock, built in combination lock, or key lock from protruding beyond door face. Pull formed in pocket. Padlock staple protruding through pocket. Provide lock hole cover plate for use with padlocks. Locking device 11 gauge steel hasp welded to locker frame; include surface for engaging the bolt of a built in combination or key lock and anti pry lug and slot to deter prying open when locked. Firmly secure rubber silencers to locker frame.
2.4.1	3 point Cremone Multipoint Latch provides an unbreakable steel handle welded securely to a 3 point cremone type latch mechanism. Latching rods 3/8” in diameter shall engage top and bottom edge of locker frame: a 1/8” thick center latch shall engage the locker jamb, enabling door to latch on three sides. Mechanism must be compatible for padlocks and built in deadbolt locks.
2.5	Hinges: Shall be 16 gauge full length continuous piano type riveted to both door and frame. Hinge shall maximize security and enhance resistance to abuse and vandalism.
2.6	Ventilation: All sides and doors 20” or higher shall be perforated with diamond shaped perforations. Optional solid doors and sides.
2.7	Body: Steel specially formed for added strength and rigidity and to ensure tight joints at fastening points.
2.8	Interior Equipment: Lockers 20” or more in height shall have a full width shelf, one double prong ceiling hook and two single prong wall hooks.
2.9	Fabrication: Pre assemble lockers by welding into one piece structures in groupings most practical for job requirements, welds free of burrs; maximum width of groups to be 54”; no bolts, nuts or rivets allowed in assembly of main locker groups.
2.10	Number Plates: Provide holes for attaching number plates. Each locker shall have a polished aluminum number plate riveted to door face with black numerals 1/2” high.
2.11	Finish: All components shall have a 2mm hybrid epoxy/polyester power, electro statically applied to ensure a uniform finished and baked to cure.
2.13	Accessories: available upon request.
2.14	Locks: available upon request.

3	Installation: Lockers shall be installed in compliance with WEC’s installation instructions and shall be level and plumb with flush surfaces and rigid attachment to anchoring surfaces
3.1	Adjust and Clean: Adjust doors and latches to operate without bidding. Verify that latches are operating satisfactory. Adjust built in locks to prevent binding of dial or key and ensure smooth operation prior to substantial completion.
3.2	Protection: Protect installed products until completion of project.